All Categories

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000
ABS Speed Sensor
Home> Products >  Motorcycle Sensor >  ABS Speed Sensor

Rear Wheel Speed ABS Sensor for Honda NSP190 — 38510-2HH-A01-M1 

The same motorcycle needs two of these, one at each end, and Honda's own numbering tells you which is which before you read anything else on the box.
Trade quantities start at a hundred units, distributor rates from there.
Rear wheel only.
The front is a different number — see section 4.
NSP190, one model
no cross-fit claim.
Active Hall
36 g, −40 to +150 °C, IP67, ISO 9001.
38520 is front, 38510 is rear
— the prefix is the map.
Do not replace both because you cannot tell which
— section 7.
A hundred to begin
a week to despatch, twelve months warranty.

Introduction

The short version

Type

Wheel speed sensor, rear

Principle

Active Hall

Output

Square wave or current pulse

Position

Rear wheel

Tone ring

Not included

Model

NSP190

Temperature

−40 to +150 °C

Ingress

IP67

Weight

36 g

Wholesale from

100 pcs

38520 is front, 38510 is rear

Honda's part numbers on this model carry the answer in the prefix. The front sensor is 38520-2HH-A01-M1. This one, the rear, is 38510-2HH-A01-M1. One digit apart, opposite ends of the machine.

Why that is worth printing. A counter conversation about an ABS lamp usually starts with "which end?" and the part number frequently settles it before anyone opens a workshop manual. A fitter holding the old sensor can read the third block and know.

And why it is also a trap. One digit apart is exactly the kind of difference that gets transcribed wrongly in a message, ordered from a photo of a screen, or assumed rather than checked. The two are not interchangeable — different lead length, different fixing, different run along the machine — and a front sensor cannot be made to work at the back.

If the number on the old part is unreadable, the position on the machine is the next best evidence, and the lead length is the giveaway: the rear runs further and differently.

What the rear one lives with

Chain lube. The rear sensor sits where fling from the chain and the sprocket arrives. A sticky film is not conductive on its own, but it collects everything the road throws up, and it packs into the gap the sensor reads across.

Sprocket and chain work. Every chain and sprocket job moves the wheel and its surroundings. A sensor that was correctly positioned now depends on being put back exactly as it was.

Rear tyre changes, which on this model are the most frequent reason the rear wheel comes out at all.

Load. A pillion and luggage put different forces through the rear end than a solo rider does, and the rear sensor and its bracket see that load path rather than the fork.

What it does not see much of is the low-speed fall on the left that damages front sensors. The rear fails from maintenance and contamination far more often than from impact — which is the opposite of its sibling at the front, and the reason the two pages read differently.

Fitment

Model

Honda NSP190

Rear wheel. The front is 38520-2HH-A01-M1 and is a separate part.

One model only. No other Honda is claimed.

Tone ring not included.

OEM cross-reference: 38510-2HH-A01-M1.

Do not replace both because you cannot tell which

On a machine with two sensors and one lamp, the temptation is to change both and be done. It is also the most expensive way to guess, and it hides the actual fault rather than fixing it.

Localise the end first.

If your tool reports speed per wheel

  • watch both numbers while the machine is pushed or ridden. Whichever end misbehaves is the end to open. That single reading is worth more than any amount of part-swapping.

If it does not

  • use the hand-spin test at both ends: ignition on, front wheel turned by hand, then rear. An active sensor reports from walking pace, so a wheel that produces no movement in the speedometer is the one to investigate — as long as the instrument is known to work.

If neither number moves

  • the fault is upstream of both: supply, ground or the module.

Two dead readings at once is almost never two failed sensors.

Why the pair-replacement habit persists. It works often enough to survive — because on a bike with a marginal rear sensor and a dirty connector, disturbing anything can restore the circuit for a few weeks. The lamp goes out, the customer is happy, and nobody learns what was actually wrong.

What to do instead. Localise, replace one, road-test, and keep the other in stock. On this model both numbers belong on the shelf; both do not belong on the invoice.

Specifications

Field

Value

Brand

RUNTONG

Part number

RB-ABS008

OEM cross-reference

38510-2HH-A01-M1

Type

ABS wheel speed sensor

Position

Rear wheel

Principle

Active Hall

Output

Square wave or current pulse

Tone ring

Not included

Mounting

Original fixing points, direct replacement

Operating temperature

−40 to +150 °C

Ingress protection

IP67

Housing

ABS plastic

Weight

36 g

Supplied with

Sensor and washer

Inner packing

Zip bag

Carton

6.5 × 6 × 5 cm, 100 pcs

Certification

ISO 9001

Warranty

12 months

Wholesale minimum

100 pcs

Custom printed carton

From 1,000 pcs

Dispatch

7 days from stock; 15–30 days to build

Freight

Air, sea, land

Packing

Each unit goes into a bag with its washer, then a plain carton of 6.5 × 6 × 5 cm holding a hundred.

36 g, and the plug is the end that breaks. It ships coiled loose with the connector protected — a drop onto that end is the only impact this shape does not survive.

One carton holds a hundred of one number. If you stock both ends for this model, keep them in separate cartons with the numbers facing out: one digit apart is a picking error waiting to happen, and the labels on the bags are the only defence.

Plain cartons, no marque. Printed from 1,000 pieces, one design, proof agreed before the run.

Fitting

1. Ignition off. Photograph the lead's route from the hub, along the swingarm, up to the frame.

2. Release the connector latch; do not use the lead as a handle.

3. One fixing bolt, fully out, body withdrawn straight.

4. Clean the face and the ring, and check that no chain lube or grit is packed into the gap.

5. Fit the washer, seat flat, torque to the machine's figure. No extra washers, no levering the bracket.

6. Route the lead as photographed, clear of the sprocket, the chain run and the tyre's path of travel.

7. Ignition on, spin the wheel, confirm the reading moves. Road-test, then re-check the lamp before handover.

Delivery, tax and warranty

Dispatch. A week off the shelf; three to four weeks once the lot is scheduled.

Freight. Air, sea or land. A hundred at 36 g is light cargo and the entry paperwork is the dominant cost.

Tax. Duty and VAT sit with the buyer unless DDP is agreed in writing. The invoice names the function — wheel speed sensor — and no manufacturer name appears on the documents, the carton or the part.

Warranty. Twelve months, batch-wide, covering sensor and seal. Outside it: impact damage, a sensing face ground through or cracked, a lead cut, crimped or spliced, a latch snapped on removal, a shell distorted by a lever or over-torque, and any extra washers under the fixing.

FAQ

Is this the front or the rear?

Rear. The front is 38520-2HH-A01-M1 — one digit different and not interchangeable.

Can I fit a front sensor at the back?

No. Different lead length, different fixing, different route.

Does it come with the ring?

No. The ring stays on the machine.

Only one lamp is on. Should I change both sensors?

No. Localise the end first — section 7 — then change one and road-test.

How do I check it before fitting?

Ignition on, spin the rear wheel by hand, watch the speedometer. An active sensor reports from walking pace.

Fewer than a hundred?

A hundred is the wholesale minimum. For one machine, buy a single unit at retail and keep the carton.

More Products

  • PD32J TRX300 TRX350 TRX400 TRX450 Fourtrax Rancher Foreman 300 350 400 450 Carburetor

    PD32J TRX300 TRX350 TRX400 TRX450 Fourtrax Rancher Foreman 300 350 400 450 Carburetor

  • Yamaha AEROX150 AEROX155 NVX155 AEROX NVX 155 Motorcycle Throttle Body

    Yamaha AEROX150 AEROX155 NVX155 AEROX NVX 155 Motorcycle Throttle Body

  • Honda 16400-K25-901 VARIO 110 125 150 160 BEAT FI Motorcycle TPS Throttle Position Sensor

    Honda 16400-K25-901 VARIO 110 125 150 160 BEAT FI Motorcycle TPS Throttle Position Sensor

  • Rear Wheel Speed ABS Sensor for Honda NSP190 — 38510-2HH-A01-M1 

    Rear Wheel Speed ABS Sensor for Honda NSP190 — 38510-2HH-A01-M1 

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Name
Company Name
Message
0/1000